These revolutionary wood lathe drives an essential addition to
every turner's toolkit.
Available in 1/2",
7/8" and 1.1/4" head in No1 and No2 morse taper and
1.1/4" head in No3 morse taper.
Their
design incorporates not just a spring loaded point in stainless steel
but also a set of razor sharp teeth which bite into the workpiece. For the novice turner this offers added security.
By winding in the
tail stock the degree of bite can be varied and the centre point
firmly located. In case of a dig-in the workpiece simply stops revolving rather than
kick back the turning chisel. This allows the beginner to use his skew
chisel with a degree of confidence.
The degree of bite which the Stebcentre creates allows for much more
demanding than would normally be expected from a conventional drive.
There is the added benefit for the production turner of allowing the
workpiece to be removed without the need to stop and re-start the
lathe. Simply wind back the tail stock and the piece can be withdrawn
safely.
Robert Sorby
Steb Headstock Drive Centres
Head
Size & Morse Taper
Woodsmith
Discount Price
No
1 MORSE TAPER
1/2"
STB 150 No1 Morse
Taper
$67.50
7/8"
STB 100 No1 Morse
Taper
$67.50
1.1/4" STB
132 No1 Morse Taper
$79.50
No
2 MORSE TAPER
1/2"
STB 250 No2 Morse
Taper
$68.50
7/8"
STB 200 No2 Morse
Taper
$68.50
1.1/4" STB
232 No2 Morse Taper
$79.95
No
3 MORSE TAPER
NO
PICTURE
1.1/4" STB
332 No3 Morse Taper
$87.75
Special
Order Only
STEBDRIVES
FOR CHUCKS
1/2"
STBCHUCK13 Stebchuck
Drive which fits neatly in most four-jaw scroll chucks.
$68.50
7/8"
STBCHUCK Temporarily
out
of
stock Stebchuck Drive which fits neatly in most four-jaw scroll chucks.
$68.50
1.1/4" STBCHUCK32 Stebchuck Drive which fits neatly in most four-jaw scroll chucks.
$79.95
Special
Order Only
REVOLVING
TAILSTOCK STEBCENTRES
No 1 MORSE TAPER Allows for basic off-centre work to
be achieved, such as carbriolet candlesticks as well as multi-sided
boxes and even small multi-sided bowls
1/2" RCSTB
150 No1 MT
Revolving Stebcentre
$80.75
7/8" RCSTB
100 No1 MT
Revolving Stebcentre
$81.50
1.1/4" RCSTB 132 No1 MT Revolving Stebcentre
$93.50
REVOLVING
TAILSTOCK STEBCENTRES
No
2 MORSE TAPER aAlows for basic off-centre work to
be achieved, such as carbriolet candlesticks as well as multi-sided
boxes and even small multi-sided bowls
1/2" RCSTB
250 No2 MT
Revolving Stebcentre
$81.75
7/8" RCSTB
200 No2 MT
Revolving Stebcentre
$82.50
1.1/4" RCSTB 232 No2 MT Revolving Stebcentre
$93.75
Scroll down for more
details...
STEB DRIVE
The original Stebcentre has been developed in two directions. The first
is the Steb Drive which fits neatly in most four-jaw scroll chucks. It
was originally designed to fit the Supernova chuck but by default fits
most others available today. The Steb Drive eliminates the need to
remove the chuck each time the turner wishes to use his Stebcentre.
STEBCHUCK
DRIVE
REVOLVING STEBCENTRE A revolutionary idea of using a revolving live centre
with the head of a Stebcentre. This allows for basic off-centre work to
be achieved, such as carbriolet candlesticks as well as multi-sided
boxes and even small multi-sided bowls when used in conjunction with an
original Stebcentre or the new Steb Drive.
